For getting rid of the old stuff, it goes out with the recycling. This video shows you the location of your oil drain plug, oil filter, oil fill cap and dipstick in addition to the steps needed to change the oil and filter in your Jetta. Six generations of body styles have been made since its inception in 1979. Removing the oil filler cap and pulling up the dipstick a few inches will help prevent a vacuum from forming and help the old oil drain out more quickly. Any information would be greatly appreciated! The Jetta was created by adding a conventional trunk to the Golf hatchback and making some front-end and interior changes.
Detach the filter wrench and continue spinning off the filter housing in the counter clockwise until it can be detached from the engine. If you can't do this, see our page to find a Volkswagen Jetta oil filter wrench. Allow the old oil to drain out of the oil filter housing. If the new o-ring is equipped with a small pull tab, position it in the up position for easy removal during the next oil change. Spin out the oil drain bolt and allow the old oil to drain out for at least a few minutes or until the flow slows to an occasional drip. All of these fluids are extremely harmful to your eyes and skin so it is important to protect yourself. Remove the screws by turning them counter clockwise with the star bit screwdriver.
I recommend buying the oil filter since it has excellent reviews on Amazon. If you have trouble turning the filter housing and your filter wrench is loose or slipping, try either wrapping the housing with some or insert a piece of newspaper or paper towel in to the wrench to give it some extra grip. Turn over the filter housing and drain out any remaining oil in to the used oil catch container. The information provided herein is a reference provided to you at no charge. Next, unscrew the small plastic end cap at the bottom of the oil filter housing attached to a black tether cable in the counter clockwise direction. Double check that the oil drain bolt and filter housing are tight before moving on the next steps.
A few compatible oil filter wrenches that are approximately 74mm in size with 14 flats include the following with their part numbers: Assenmacher Specialty Tools 74mm , , Hazet 2169 74. Do not over tighten the oil drain bolt to prevent from stripping the aluminum threads. You may not need to pour in the entire 6. First major thing it's needed. There are 4 screws on the passenger side and another 4 on the driver's side of the panel. Looks like that should be the correct oil for yours as well.
If your vehicle was originally charged with R12 refrigerant, for example, the oil type specified, 'mineral', will not apply. The first three steps are to warm up the engine for a few minutes, park the car on a level surface and then shut off the engine. Gently push the drain nipple up at an angle with a small flathead screwdriver until it stays in place. Tighten the oil drain bolt with the 19mm socket and ratcheting wrench in the clockwise direction to just past hand tight or about 22 ft-lbs 30 Nm of torque. I was wondering if any of you with Jettas do your own oil changes? You never know what could be dripping down from the engine, battery acid, engine coolant, brake fluid, etc. Try to avoid rounding off the sides of the plastic filter housing, which may make it more difficult to remove during future oil changes. The round black plastic oil filter housing is located just in front of the black metal oil pan and it is surrounded by rubber hoses.
Push the new cartridge oil filter down in to the housing until it clicks securely in to place. When you change your own oil, you know that you are putting quality oil in your Jetta and that the filter is being changed too. Once the cover is removed, you'll see the the reddish orange drain nipple. Be sure to record the oil change in your Jetta's service records. It's just a fantastic car.
Line up the tabs on the front edge of the plastic engine underside cover and re-insert them in to the their corresponding slots by sliding the cover forwards. Volkswagen recommends replacing the oil drain bolt at every oil change. Double check that the drain plug is tight before moving on to the next steps. Insert an automotive funnel in to the oil filler hole. Slide the used oil catch basin to just below the oil drain plug. Spin in the oil drain bolt by hand in the clockwise direction to prevent it from becoming cross threaded. Donations are not tax deductible.
Where I live you have to put it in a gallon milk jug and set it next to the bin. We recommend wearing safety glasses whenever you are working under your Jetta. It's acceleration is obviously not the best in the world, but has plenty of torque. Raise the front passenger side of the vehicle with the floor jack and securely support it with the two. Do not over tighten the oil filter housing to avoid damaging the plastic housing, the threads or the rubber o-ring since it may cause an oil leak. Set the plastic cover and the 8 screws aside in a safe place.
Carefully pour in about 5. Please help support this website by shopping at. Pull out the dipstick, wipe it clean, re-insert it, and pull it out again to check the oil level. The silver metal oil drain bolt is located at the rear edge of the black metal oil pan towards the back of the engine bay. If it isn't printed on the oil cap, check your owners manual for the exact type before adding new oil. I prefer to raise just the front passenger side of the car to access the underside of the engine and leave the three other wheels on the ground for extra safety. If you do I hsve a few other questions.